HMS Intesis KNX User Manual Download Page 14 | Manualshive

Page: 14 / 26

HMS Intesis KNX User Manual Download Page 14

Intesis

TM

KNX

– BACnet Client

User Manual r1.2 EN

© HMS Industrial Networks S.L.U - All rights reserved

This information is subject to change without notice

URL

http

s

://www.intesis.com

14 / 26

5

Set-up process and troubleshooting

Pre-requisites

It is necessary to have a KNX installation, device or interface operative and well connected to the corresponding KNX
port of Intesis and a BACnet MSTP or BACnet IP installation connected to their corresponding ports as well.

Connectors, connection cables, PC to use the configuration tool and other auxiliary material, if needed, are not
supplied by HMS Industrial Networks S.L.U for this standard integration.

Items supplied by HMS Networks for this integration are:

•

Intesis gateway.

•

Mini-USB cable to connect to PC

•

Link to download the configuration tool.

•

Product documentation.

Intesis MAPS. Configuration & monitoring tool for Intesis BACnet series

5.2.1 Introduction

Intesis MAPS is a Windows

®

compatible software developed specifically to monitor and configure Intesis KNX series.

The installation procedure and main functions are explained in the

Intesis MAPS User Manual for KNX

. This

document can be downloaded from the link indicated in the installation sheet supplied with the Intesis device or in
the product website at

www.intesis.com

In this section, only the specific case of BACnet to KNX systems will be covered.

Please check the Intesis MAPS user manual for specific information about the different parameters and how to
configure them.

5.2.2 Connection

To configure the Intesis connection parameters press on the

Connection

button in the

menu bar

.

Figure 5.1

MAPS connection

«
...
12
13
14
15
16
...
»

Summary of Contents for Intesis KNX



























Reviews:

No comments