HMS Networks Intesis DALI User Manual Download Page 26

Page: 26 / 34

Intesis

KNX

– DALI

User Manual r1.1 EN

This information is subject to change without notice

URL

http

://www.intesis.com

26 / 34

Electrical & Mechanical Features

Enclosure

Plastic, type PC (UL 94 V-0)
Net dimensions (d

h): 90x88x56 mm

Recommended space for installation (d

h): 130x100x100mm

Color: Light Grey. RAL 7035

Battery

Size: Coin 20mm x 3.2mm
Capacity: 3V / 225mAh
Type: Manganese Dioxide Lithium

Mounting

Wall.
DIN rail EN60715 TH35.

Console Port

Mini Type-B USB 2.0 compliant
1500VDC isolation

Terminal Wiring

(for power supply and
low-voltage signals)

Per terminal: solid wires or stranded wires (twisted or with ferrule)

1 core: 0.5mm

… 2.5mm

2 cores: 0.5mm

… 1.5mm

3 cores: not permitted

If cables are more than 3.05 meters long, Class 2 cable is required.

USB port

Type-A USB 2.0 compliant
Only for USB flash storage device

(USB pen drive)

Power consumption limited to 150mA

(HDD connection not allowed)

Power

1 x Plug-in screw terminal block (3 poles)

Positive, Negative, Earth
24VDC

Push Button

Button A: Check the user manual
Button B: Check the user manual

Operation
Temperature

0°C to +60°C

Ethernet

1 x Ethernet 10/100 Mbps RJ45
2 x Ethernet LED: port link and activity

Operational
Humidity

5 to 95%, no condensation

Port A

1 x KNX TP-1 Plug-in screw terminal block orange (2 poles)

2500VDC isolation from other ports
KNX power consumption: 5mA
Voltage rating: 29VDC

1 x Plug-in screw terminal block green (2 poles)

Reserved for future use

Protection

IP20 (IEC60529)

LED
Indicators

10 x On board LED indicators

1 x Error LED
1 x Power LED
2 x Ethernet Link/Speed
2 x Port A TX/RX

2 x Port B TX/RX

1 x Button A indicator
1 x Button B indicator

Switch A

(SWA)

1 x DIP-Switch for serial EIA485 configuration:
Reserved for future use

PORT B

1 x Serial EIA232 (SUB-D9 male connector)

Reserved for future use

1 x Serial EIA485 Plug-in screw terminal block (3 poles)

B1, B2
1500VDC isolation from other ports
DALI power consumption: 240mA
Voltage rating: 16VDC

(except PORT B: EIA232)

Switch B

(SWB)

1 x DIP-Switch for serial EIA485 configuration:

Reserved for future use

Summary of Contents for Intesis DALI



































Search results

Summary of Contents for Intesis DALI

Reviews:

Related manuals for Intesis DALI

Brands by name

Popular brands

HMS Networks Intesis DALI, User Manual

Search results

Summary of Contents for Intesis DALI

Reviews:

Related manuals for Intesis DALI

Brands by name

Popular brands