Quick Reference Installation Guide
HM ELECTRONICS, INC.
2848 Whiptail Loop, Carlsbad, CA 92010 USA
Phone: 1-800-848-4468 Fax: 858-552-0172
Website: www.hme.com Email: [email protected]
HME# PUB - 00074
Rev C 02/07/22
NEXEO | HDX™ RT7000
REMOTE TRANSCEIVER
The RT7000 (Fig. 1) is a transceiver used to facilitate communication
with the NEXEO | HDX™system. It uses a wired connection to the
base station but is wireless for headset communication. Up to four
RT7000s can be connected to the base station for greater coverage.
TOOLS/EQUIPMENT REQUIRED
• Drill and drill bit set
• Screwdriver (Phillips #2), tape measure, pencil/maker
• Cable Pull Equipment (fish stick/tape, pull string, cable ties, etc.)
• Safety glasses, ladder
INSTALLATION, SETUP, AND OPERATION
1. Survey the premises to determine a good location to mount the
RT7000 (see "RT7000 Notes" on page 3 and Fig. 12 on page 4).
2. Route the Ethernet cable from the base station to the RT7000
location.
3. Loosely mount the RT7000 (until range tested with the Installa-
tion Wizard in step 7.
4. Connect the Ethernet cable to the RJ45 port on the rear of the
RT7000 (see Fig. 2) and the other end to one of the available
ports on the base station (see Fig. 3, Fig. 11, and Table 2). The
base station provides power for the RT7000. The center LED on
the front of the RT7000 is the power indicator. It turns on solid
green once power is connected (see Fig. 9 on page 3).
5. One of the outer LEDs (numbered 1 to 4) also turns on and
initially flashes a different color as the RT7000 completes a scan
of the environment to find an available channel (see Table 1).
Once the scan is finished, this outer LED also turns solid green
(see Fig. 9 on page 3). During this time, the base station HOME
screen also provides a color-coded status for the RT7000 (it is
labeled as "Transceivers," see Fig. 4). The
indicator
initially turns
(yellow) while scanning for a channel before
turning
(green) when one is found. This can take a few
minutes.
Fig. 4
6. At the base station, go to
SYSTEM,
log in,
then tap the
TROUBLE-
SHOOTING
tab and select “Installation Wizard” from the drop-
down list. Tap the “Start Installation Wizard” button. This opens
the Installation Wizard, as shown in Fig. 5.
Fig. 1
Rear View
Fig. 2
Fig. 3
1
2
3
4
RT7000 TRANSCEIVER
Front View
RT7000 TRANSCEIVER
Rear View
THIS SIDE UP
Mounting Holes
RJ45 Port
for Ethernet cable
NEXEO BASE STATION
PCBA (Partial)
Remote
XCVR 1
Remote
XCVR 2
Remote
XCVR 3
Remote
XCVR 4
Ethernet/
Network
Telephone
Interface
Timer Greet
Veh Detect 1
Timer Greet
Veh Detect 2
Veh Detect
Inputs
Alert
Inputs
Remote
Switches
Early
Warnings
Power
In
DC +
DC -
GND
Micro
USB
J200
J600
J201
J800
J801
J802
J805
J804
J803
J2003
J3000
J4500
J4501
J1400
J3200
J3400
J3600
J3800
1
1
1
1
1
1
1
1
1
1
1
Serial
Debug
USB
J?301
J?300
J1
PCBA
Side View Detail
Ethernet
(Network)
Remote
Module 1
Remote
Module 2
Remote
Module 3
Remote
Module 4
Power
Transceiver (x4)
1
2
3
4
Vertical Mount Only
(this way up)
REMOTE TRANSCEIVER
(RT7000)
