Hitecsa EQU-PF 2100, Installation, User And Maintenance Manual

Page: 51 / 61

53
ENCLOSED DOCUMENTS
Table “A”: Technical Data
EQU-PF Model 270 280 290 2100 2115 2130 2145 2160
Nominal cooling capacity (*) kW 70,3 79,5 88,0 101,2 114,5 126,0 143,0 161,0
E.E.R. (3
rd
step, 100%) 2,60 2,68 2,60 2,50 2,68 2,68 2,64 2,67
E.E.R. (3
rd
step, 100%)
EN 14511 05/11 (250kPa residual)
3,27 3,28 3,12 3,15 3,33 3,24 3,32 3,26
E.S.E.E.R. 3,25 3,47 3,25 2,98 3,35 3,48 3,30 3,46
E.S.E.E.R. + 3,75 4,02 3,77 3,44 3,89 4,00 3,80 3,99
E.S.E.E.R. EN 14511 05/11 (250kPa residual) 5,56 6,02 5,86 5,74 5,43 5,42 5,32 5,37
E.S.E.E.R + EN 14511 05/11 (250kPa residual) 6,42 6,97 6,79 6,63 6,30 6,24 6,13 6,19
Sound power level (3
rd
step, 100%) (***) dB(A) 85 85 86 88 88 88 89 89
Scroll/step compressor n° 2/3 2/2 2/3 2/3 2/3 2/2 2/3 2/2
Circuits n° 1 1 1 1 1 1 1 1
Fans n° x kW 2x2.13 2x2.13 2x2.32 3x2.33 3x2.12 3x2.16 4x2.25 4x2.25
Fan nominal air flow m³/h 26000 26000 27000 39000 39000 39000 52000 52000
Fan maximum available static head Pa 250 250 250 250 250 250 250 250
Water side heat exchanger water content l 5,0 6,1 6,1 6,9 8,4 8,4 9,9 11,1
Water side heat exchanger nominal flow (*)
Water side heat exchanger m³/h
kPa
12,1
42
13,6
37
15,1
45
17,4
47
19,6
42
21,6
51
24,5
49
27,6
50
nominal pressure drops (*)
P1 residual head (*) kPa 134 129 119 110 106 90 141 122
P2 residual head (*) kPa 254 247 248 238 232 214 270 249
ASP1 residual head (*) kPa 131 125 117 108 103 86 136 117
ASP2 residual head (*) kPa 251 243 246 236 229 211 266 244
Water tank content (ASP1/ASP2) l 250 250 250 250 450 450 450 450
Amount of R410A refrigerant See serial number plate
Amount of Polyester oil See compressor plate
Electrical data 270 280 290 2100 2115 2130 2145 2160
Absorbed power (*) (■)
kW 27,0 29,7 33,8 40,5 42,7 47,0 54,2 60,4
Pump absorbed power (P1/ASP1) / (P2/ASP2) kW 1,1/2,2 1,1/2,2 1,5/3,0 1,5/3,0 1,5/3,0 1,5/3,0 2,2/4,0 2,2/4,0
Electrical power supply V-ph-Hz 400
– 3+N – 50
Auxiliary power supply V-ph-Hz 230
– 1+N – 50
Control power supply V-ph-Hz 24
– 1 – 50
Nominal current (■)
A 47,3 51,9 54,0 67,6 77,6 84,5 95,0 106,6
Maximum current
(■)
A 64,3 68,7 72,7 85,4 91,2 100,2 116,1 127,1
Starting current (■)
A 207 212 262 313 319 327 368 382
Pump absorbed current (P1/ASP1) / (P2/ASP2) A 2,6/5,0 2,6/5,0 3,5/6,0 3,5/6,0 3,5/6,0 3,5/6,0 5,0/8,1 5,0/8,1
Dimensions 270 280 290 2100 2115 2130 2145 2160
Width (a) mm 1100 1100 1100 1100 1100 1100 1100 1100
Height (b) mm 1920 1920 1920 1920 2320 2320 2320 2320
Depth (c) mm 3650 3650 3650 3650 4450 4450 4450 4450
Heat exchanger inlet/outlet connections Ø
2” 2” 2” 2” 2” 2” 2” 2”
DS/RC100 inlet/outlet connections Ø
2” 2” 2” 2” 2” 2” 2” 2”
(*) In the following conditions: Condenser inlet
air temperature 35°C; chilled water temperature
7°C; temperature differential at evaporator 5°C.
(***) Sound power level in dB(A) on the basis of
measurements taken in accordance with RS
6/C/005-2009. The noise data refers to the units
without the pump.
(■)
Pumps excluded.
Nota Bene:
The E.E.R. and C.O.P calculation does not
consider the absorption of the pumps.
The EER, ESEER and COP calculations
according to EN 14511 05/11 (250kPa residual)
refer to the versions without pumps.
The starting current reduces by 25% with the
SFS accessory
The machine decreases its noise below the
nominal value indicated in the table when the
outdoor air temperature is below 35°C and
condensation control is present.
If the INS accessory is present, the sound
power Lw decreases by 2 dB(A).