Hitecsa 1602.2 Installation, Operation & Maintenance Manual Download Page 7

 
 
 

 

IOM_UMXCBA-UMXCA_801.1a4502.2_208027_200201_EN

 

UMXCBA/UMXCA

 

CONDENSER UNITS WITH 
COMPRESSOR AND AXIAL FAN

 

 

 

SAFETY INSTRUCTIONS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

  

DANGER

 

 

• Should it be necessary to open the electrical box in order to get inside the equipment, it is 
COMPULSORY to plug the main power cable out prior to this operation. The equipment MUST 
ALWAYS BE FREE OF VOLTAGE when opening the electrical box. 
 
 

• Do not touch or adjust the safety devices inside the unit. For repairs use only original spare parts 

and install them properly in the same position where the old parts were fitted. 
 
• The installation and maintenance of air conditioning equipment may be dangerous due to the 
pressure of the system, the high temperature of some of its parts and the electrical components.  
 
• Do not install the unit in an explosive atmosphere. 

 

 

 

 
 
 

 

Only  qualified  and  trained  service  staff  (technical  service)  is  authorized  to  carry  out  installation, 
commissioning  and  maintenance.  Unqualified  personnel  will  carry  out  basic  tasks  only  such  as 
cleaning and replacement of filters, or filter cleaning (excluding the refrigerant filters), etc.

… 

 

Prevent access to children to avoid that they play with the equipment. 

 

For all visits, follow carefully all recommended precautions: the instructions recommended in the 
installation, operation and maintenance manual, as well as the precautions stated on the stickers 
placed on the unit. Do not forget to strictly follow any other legal safety instructions. 

 

DO NOT introduce objects into the air inlets or outlets that might be drawn into the fan, people, etc. 

 

Use  safety  glasses,  work  gloves  and  any  other  safety  accessory  that  may  be necessary  for  the 
operation. 

 

For brazing operations use a quenching cloth and make sure you have a fire extinguisher close to 
you. 

 

This product contains fluorinated greenhouse gases. In case of leakage air may be displaced which 
may cause lack of oxygen. 

 

•  

Please follow all the safety recommendations carefully. 

 

 

 

ATTENTION!

 

 

Before starting any installation, service or maintenance operation, turn the main power switch 

off in order to avoid electrical discharges that may cause personal injuries.

 

WARNING 

Summary of Contents for 1602.2








































Reviews: