manualshive.com logo in svg

Hitecsa 1602.2, Installation, Operation & Maintenance Manual, Page: 31 / 39

Share
Download
Hitecsa 1602.2 Installation, Operation & Maintenance Manual Download Page 31

 
 
 

 

29 

IOM_UMXCBA-UMXCA_801.1a4502.2_208027_200201_EN

 

UMXCBA/UMXCA

 

CONDENSER UNITS WITH 
COMPRESSOR AND AXIAL FAN

 

 

OPERATION 

pGD1 or Mini PGD THERMOSTAT 

Local Network 

Information represented in the selected unit: 

 

Unit: 01 

Represents the unit number to which the terminal is connected.

 

12:00 

Indicates the actual time (only if the clock card is installed, this configuration is optional) 

  /  

 

Indicates the mode and operation of the unit, 

 cold and 

 heat pump. 

Al 

Indicates whether the unit has an active alarm 

20.0 ºC 

Indicates the return temperature 

Unidad 
Off 

Indicates unit status, multiple labels can be output Unit off per hour phase - Off Remote Unit 

 

Alarms 

 

All alarms shown on the thermostat, except those with category WARNING, will cause the unit to stop. 
 

Canceling alarms: 

 

 

  This button lights up if the unit has an active alarm, pressing the button will delete the 

acoustic alarm, after a second press if the alarm is cleared the alarm will be cleared. 

  If it is not solved, contact the technical service. 

-

 

Alarm Messages Description: pGD1 Optional (HITSAA01) 

 

ALARM MESSAGES pGD1  (Optional: 

HITSAA01

) 

Message in Display 

Type 

Alarms Clock card error or not connected  

Warning 

Alarms Probe B01 broken or disconnected  

Warning 

Alarms ThTune offline 

Alarm 

Alarms ThTune n. Temperature probe broken or not working 

Warning 

Alarms ThTune n. Humidity probe broken or not working 

Warning 

Alarms ThTune n. clock card error 

Warning 

Alarms Serious High Pressure Switch  

Alarm 

Alarms serious High Pressure  Switch Circuit 2 

Alarm 

Alarms High Pressure Switch  

Alarm 

Alarms High Pressure Switch circuit 2  

Alarm 

Alarms Low Pressure Switch  

Alarm 

Alarms Low Pressure Switch circuit 2 

Alarm 

Alarms Minimum Pressure Switch  

Alarm 

Alarms Minimum Pressure Switch Circuit 2 

Alarm 

Alarms Serious Low Pressure Switch  

Alarm 

Alarms Serious Low Pressure Switch Circuit 2 

Alarm 

Alarms Serious Minimum Pressure Switch  

Alarm 

Alarms Serious Minimum Pressure Switch Circuit 2  

Alarm 

Alarms Thermic Supply Fan 

Alarm 

Alarms Thermic Outdoor Fan / Compressor  

Alarm 

Alarms Thermic Outdoor Fan / Compressor circuit 2  

Alarm 

Alarms low refrigeration level 

Alarm 

Alarms low refrigeration level circuit 2  

Alarm 

 Alarms Probe B11 broken or disconnected 

Alarm 

 Alarms Probe B12 broken or disconnected  

Alarm 

 Alarms Press ENTER for History of Alarms 

Alarm 

 
 

 

 

Summary of Contents for 1602.2








































Reviews:

No comments