INSTRUCTION MANUAL
PHANTOM X4 CHARGER
PART NO. 44525
INTRODUCTION
CONTENTS
The Phantom X4 Charger is a four-channel battery charger designed and built exclusively for DJI
Phantom™ 3 and DJI Phantom™ 4* Smart Batteries. This charger is capable of charging, storing and
deep cycling four DJI™ smart batteries simultaneously. Two smart devices can be charged via USB
ports and two remote controllers can be charged at the same time.
This unit is simple to use, but the operation of a sophisticated automatic charger such as the Phantom
X4 Charger does require some knowledge on the part of the user. These operating instructions are
designed to ensure that you quickly become familiar with its functions. It is therefore important that
you read through the Operating Instructions, Warning and Safety Notes before you attempt to use this
charger for the first time.
* By using optional adaptor part number 61116 sold separately.
™ DJI, DJI Phantom are trademarks of SZ DJI Technology Co., Ltd
1. Connect the Power Cord to the AC socket (100-240V).
2. Turn ON the Power Switch. The LED display shows “CHG” and the
charger is in CHARGE MODE.
3. Insert the battery into the battery slot. The Phantom X4 Charger will
communicate with the battery and send the battery into CHARGE
MODE automatically. If the battery level is above 95%, turn on the battery
before charging.
4.The battery’s green LED will be blinking and the LED display will show
the charging percentage of the battery. When the battery is fully charged,
the battery’s green LED’s will turn OFF and the charging station will beep
5 times. Promptly remove the battery from the Phantom X4 Charger.
1. Phantom X4 Charger
2. Power Cord
3. USB Charge Cable (Micro B type)
4. Remote Controller Charging Cable x 2
Insert the Battery
Into the Battery Slot
CHARGING YOUR BATTERIES
1
2
WARNING: THE CHARGING AND DISCHARGING OF LITHIUM CHEMISTRY BATTERIES
CAN BE DANGEROUS. FAILURE TO FOLLOW THESE EXPLICIT WARNINGS CAN
RESULT IN PROPERTY DAMAGE AND/OR LOSS OF LIFE.
A
NEVER LEAVE YOUR CHARGER UNATTENDED WHILE IN OPERATION.
A
NEVER CHARGE ON OR AROUND COMBUSTIBLE MATERIALS.
A
NEVER CHARGE A DAMAGED BATTERY PACK.
A
THIS CHARGER IS DESIGNED AND BUILT EXCLUSIVELY FOR DJI PHANTOM™ 3 AND DJI
PHANTOM™ 4 SMART BATTERIES ONLY.
A
IT IS NOT RECOMMENDED THAT YOU CHARGE AFTERMARKET BATTERIES DESIGNED FOR
THESE DEVICES.
A
THE ALLOWABLE AC INPUT VOLTAGE IS 100~240V.
A
KEEP THE CHARGER WELL AWAY FROM DUST, MOISTURE, RAIN, HEAT, DIRECT SUNLIGHT
AND EXCESSIVE VIBRATION.
A
IF THE CHARGER IS DROPPED OR SUFFERS ANY TYPE OF IMPACT, IT SHOULD BE
INSPECTED BY AN AUTHORIZED SERVICE STATION BEFORE USING IT AGAIN.
A
DURING CHARGING, THE CHARGER MUST BE PLACED IN A WELL-VENTILATED AREA.
A
WHEN THE CHARGER IS NOT IN USE, MAKE SURE TO TURN IT OFF.
FAILURE TO FOLLOW THESE WARNINGS CAN BE CONSIDERED NEGLIGENCE BY THE
OPERATOR AND MAY NEGATE ANY CLAIMS FOR DAMAGES INCURRED.
Hitec RCD USA will not be held responsible for any damages or injuries that may occur by persons
who fail to follow these warnings or who fail to properly follow the instructions in this manual.
Warning
OPTIONAL PART
Cable Adaptor for a DJI PHANTOM™ 4 Battery
Cooling Fan
Charging Port
for Remote Controller
USB Power
for Smart Device
Output Power
Indicator
Storage Button
Cycle Button
Battery Voltage
LED Display
Battery Slot
Carrying Handle
Cooling Fan
Power Switch
AC Socket
100-240V
Battery Level
Percentage
1
2
4
3
Part No. 61116
Optional Adaptor Sold Seperately
