background image

• Certificates for RMI communication are updated asynchronously. The

process takes about two minutes.

• If the service processor certificate is updated while Hitachi Command Suite

is being set up, the setup operation will fail.

• Updating the SSL certificate might change the system drastically and may

lead to service processor failure. Therefore take sufficient care to consider
the content of the certificate and private key to be set.

• After the certificate update is complete, depending on the environment,

the service processor can take 30 to 60 minutes to restart.

Returning the certificate to default

You can return the certificate that was updated by the procedure in 

Updating

a signed certificate on page 219

 back to default.

Before you begin

• You must have the Storage Administrator (Initial Configuration) role to

perform this task.

• You must be logged into the SVP.
• A private key (.key file) has been created. Make sure that the file name is

server.key

. See 

Creating a private key on page 215

.

• The passphrase for the private key (server.key file) is released.
• A signed public key certificate (.crt file) has been acquired. Make sure that

the file name is 

server.crt

. See 

Creating a public key on page 215

.

• The private key (.key file) must be in PEM format. You cannot use DER

format.

• The signed public key certificate (.crt file) must be in X509 PEM format.

You cannot use X509 DER format. See 

Obtaining a self-signed certificate

on page 217

.

• The passphrase for the private key (server.key file) must be released.

Procedure

1.

Close all Device Manager - Storage Navigator sessions on the SVP.

2.

Open a command prompt window with administrator permissions.

3.

In the folder where the .bat file is located, execute the following

command:

C:\MAPP\wk\Supervisor\MappIniSet>MappApacheCrtInit.bat

4.

A completion message box displays. Press any key to acknowledge the

message and close the message box.

5.

Close the command prompt window.

220

Setting up security

System Administrator Guide for VSP Gx00 models and VSP Fx00 models

Summary of Contents for VSP F400































































































































































































































































































































































































































Reviews: