Hitachi HVM Navigator V03-06 User Manual Download Page 303

Page: 303 / 312

Troubleshooting

6-41

HVM Navigator User's Guide - Migration

Detailed error information detected by Recovery module

Format

“EMG” op1 : don’t_care : don’t_care : (op3) : ”Recovery” : message

•

“EMG”: Fixed characters meaning error message.

•

“Recovery”: Fixed characters meaning Recovery module.

•

don’t_care: Values at this position are negligible.

•

op1: 1st operand that identifies error detail in hexadecimal code. See
Description.

•

op3: 3rd operand that identifies reason in hexadecimal code. See
Description.

•

Message: Error detail in text. See Description.

Table 6-5 Error message detected by Recovery module

op1

op3

Message [interpretation]

Suggested action

0x00 00000000 0000 10 0x01 Connection refused (MMC-MMS)

[Migration Console module (MMC) cannot
connect to Migration Management

module (MMS).]

Check the following, make corrections if
necessary, and then retry recovery

operation:
The specified server blade (HVM) is up
and running.
Communication to the IP address of the

specified server blade is established.

0x00 00000000 0010 10 0x01 Connection refused (MMS-Specified blade

IP=%s)
[Recovery operation terminated by a

network failure.]

Check for recovery of connection
between the management server and the
specified server blade, and then retry

recovery operation.

0x00 00000001 0011 10
0x00 00000001

0031 10

0x01 The specified LPAR is busy, please wait

until another migration is completed.

Wait until the ongoing migration is
complete and then retry recovery

operation.

0x00 00000016 0011 00
0x00 00000016 0031 10
0x00 00000023 0011 10
0x00 00000023 0031 10

0x01 Loading recovery files failed. Hardware failures may have occurred.

Reading recovery file has failed.

Hardware might be failed.
Retry the recovery procedure after
executing procedure of failure detection
(Saves the configuration information by
pressing F9 key).

0x00 00000021 0011 10
0x00 00000021 0031 10
0x00 00000027 0011 10
0x00 00000027 0031 10

0x01 The MMS could not recover the specified

LPAR from a failed-migration state
because of activated LPAR.
[Recovery operation failed because the

specified LPAR is in Activate state.]

Deactivate the specified LPAR and then
retry recovery operation.

0x00 00000029 0011 10
0x00 00000029 0031 10

0x01 The specified LPAR was not recover from

a failed-migration state, and try again.

[Recovery operation failed.]

Retry recovery operation.

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 303 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: