manualshive.com logo in svg

Hitachi H8/3635, Hardware Manual

Looking for a comprehensive Hardware Manual for the Hitachi H8/3635? Look no further! Download the user manual for free from manualshive.com, your ultimate source for manuals. Discover step-by-step instructions and detailed information about your product, ensuring optimal utilization and hassle-free experiences with the Hitachi H8/3635.

Share
Download
background image

98

5.5

Subsleep Mode

5.5.1

Transition to Subsleep Mode

The system goes from subactive mode to subsleep mode when a SLEEP instruction is executed
while the SSBY bit in SYSCR1 is cleared to 0, LSON is set to 1, and bit TMA3 in TMA is set
to 1.

In subsleep mode, operation of on-chip peripheral modules other than timer A and timer G is
halted. As long as a minimum required voltage is applied, the contents of CPU registers and some
registers of the on-chip peripheral modules*, and the on-chip RAM contents, are retained. I/O
ports keep the same states as before the transition.

Note: * The contents of SCI3, DTMF generator registers are reset.

5.5.2

Clearing Subsleep Mode

Subsleep mode is cleared by an interrupt (timer A, timer G, IRQ

0

 to IRQ

4

, WKP

0

 to WKP

7

) or by a

low input at the 

RES

 pin.

Clearing by Interrupt: When an interrupt is requested, subsleep mode is cleared and interrupt
exception handling starts. Subsleep mode is not cleared if the I bit of CCR is set to 1 or the
particular interrupt is disabled in the interrupt enable register.

Clearing by 

RES

 Input: Clearing by 

RES

 input is the same as for standby mode; see 5.3.2,

Clearing Standby Mode.

Summary of Contents for H8/3635




















































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3635

Walchem W100 Troubleshooting Manual preview
W100
Brand: Walchem Pages: 10
Samsung SSA-P400 User Manual preview
SSA-P400
Brand: Samsung Pages: 27
Safran MorphoAccess SIGMA Extreme Series Installation Manual preview
MorphoAccess SIGMA Extreme Series
Brand: Safran Pages: 79
Lawler 805 Installation & Maintenance Manual preview
805
Brand: Lawler Pages: 5
tams elektronik ABC-1 Manual preview
ABC-1
Brand: tams elektronik Pages: 12
Mackie Remote 48 Brochure preview
Remote 48
Brand: Mackie Pages: 4
Maclaren twin techno User Manual preview
twin techno
Brand: Maclaren Pages: 15
Maclaren mx3 Instructions Manual preview
mx3
Brand: Maclaren Pages: 9
Maclaren Major Elite User Manual preview
Major Elite
Brand: Maclaren Pages: 40
Patron Buggy User Instructions preview
Buggy
Brand: Patron Pages: 17
C&C Atlas Series Installation, Operation And Maintenance Manual preview
Atlas Series
Brand: C&C Pages: 17
Raynor Smart Control Panel 880RGD Quick Manual preview
Smart Control Panel 880RGD
Brand: Raynor Pages: 4
Baby Trend EZ Ride5 ST40 Instruction Manual preview
EZ Ride5 ST40
Brand: Baby Trend Pages: 12
AUMA GSTI 25.1 Operating Instructions Manual preview
GSTI 25.1
Brand: AUMA Pages: 24
VALSTEAM ADCA TSS 7 Installation And Maintenance Instructions preview
TSS 7
Brand: VALSTEAM ADCA Pages: 4
Gecko MC-MP Service Manual preview
MC-MP
Brand: Gecko Pages: 82
BQT BioX Series Installation Manual preview
BioX Series
Brand: BQT Pages: 2
Multitech MultiConnect Dragonfly MTQ-MNA1-B01 Device Manual preview
MultiConnect Dragonfly MTQ-MNA1-B01
Brand: Multitech Pages: 45

Brands by name

Popular brands

Load more brands