Hitachi H8/3635 Hardware Manual Download Page 32 | Manualshive

Page: 32 / 403

background image

22

8. Memory Indirect—@@aa:8: This mode can be used by the JMP and JSR instructions. The
second byte of the instruction code specifies an 8-bit absolute address. The word located at this
address contains the branch destination address.

The upper 8 bits of the absolute address are assumed to be 0 (H'00), so the address range is H'0000
to H'00FF (0 to 255). Note that with the H8/300L Series, the lower end of the address area is also
used as a vector area. See 3.3, Interrupts, for details on the vector area.

If an odd address is specified as a branch destination or as the operand address of a MOV.W
instruction, the least significant bit is regarded as 0, causing word access to be performed at the
address preceding the specified address. See 2.3.2, Memory Data Formats, for further information.

2.4.2

Effective Address Calculation

Table 2.2 shows how effective addresses are calculated in each of the addressing modes.

Arithmetic and logic instructions use register direct addressing (1). The ADD.B, ADDX, SUBX,
CMP.B, AND, OR, and XOR instructions can also use immediate addressing (6).

Data transfer instructions can use all addressing modes except program-counter relative (7) and
memory indirect (8).

Bit manipulation instructions use register direct (1), register indirect (2), or 8-bit absolute
addressing (5) to specify a byte operand, and 3-bit immediate addressing (6) to specify a bit
position in that byte. The BSET, BCLR, BNOT, and BTST instructions can also use register direct
addressing (1) to specify the bit position.

«
...
30
31
32
33
34
...
»

Summary of Contents for H8/3635




















































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8/3635

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Smart-MPPT Li Series

Brand: Y-Solar Pages: 6

Brand: 1Control Pages: 8

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands