manualshive.com logo in svg

Hitachi DS 14DMR, Technical Data And Service Manual, Page: 8 / 59

Share
Download
Hitachi DS 14DMR Technical Data And Service Manual Download Page 8

--- 5 ---

Fig. 3

Selling points of the Models WR 14DMR/WR 18DMR

Powerful tightening torque

    WR 14DMR: 200 N.m (2040 kgf.cm, 1770 in-lbs.)

    WR 18DMR: 220 N.m (2245 kgf.cm, 1950 in-lbs.)

Both the Models WR 14DMR and WR 18DMR are equipped with a relatively inexpensive magnet and the

entire length is significantly shorter than the previous models respectively.  However, the performance is

superior to the competitors thanks to the large hammer and the optimized impact timing.  Comparison of

measured data with the previous model and the competitors is shown below.

(1) Tightening torque comparison

Figure 3 shows the torque required for tightening an M16 F10T bolt in 3 seconds with a hexagon socket

(40 mm long).

    WR 14DMR: 25 % higher than P3

    WR 18DMR: 20 % higher than P4

* The data above are intended for reference purposes only because actual tightening torque will vary
  depending on tightening conditions.

T

ightening torque

0

50

100

150

WR 14DMR

(14.4 V)

238

WR 14DM

(14.4 V)

P3

(14.4 V)

kgf

.

cm

242

207

200

250

0

500

(434 in-lbs.)

1000

(868 in-lbs.)

1500

(1302 in-lbs.)

2000

(1736 in-lbs.)

2500

(2710 in-lbs.)

N

.

m

WR 18DMR

(18 V)

P4

(18 V)

232

182

Summary of Contents for DS 14DMR




























































Reviews:

No comments