Hitachi CP-C9SM Page 39 Service Manual Download

Page: 39 / 72

CP-S335(C9SM)/CP-X340(C9X)/CP-X345(C9XM)

3. Putting the power supply unit together after the

maintenance of the POWER UNIT (CIRCUIT)

and/or the POWER UNIT (BALLAST).

WARNING

Assemble the power supply unit
with care to achieve the required
insulation. Incorrect assembly
could cause a ﬁ re and/or an elec-
tric shock.

(1) Attaching the Power Center Sheet

(2) Attaching the Power Side Sheet

Warning

Hook claw.

Power Center Sheet

POWER-BRACKET

Insert sheet between POWER BOARD

(CIRCUIT) and the Power Side Sheet.

Power Side Sheet

POWER BOARD (CIRCUIT)

Warning

POWER-BRACKET

Power Sheet

Insert tab into slit.

Warning

(3) Attaching the Power Sheet

Attach Power Sheet so that its shaded

edge cannot contact to POWER UNIT

(BALLAST).

Power Sheet

Clip tab.

Warning

Summary of Contents for CP-C9SM









































































Search results

Summary of Contents for CP-C9SM

Reviews:

Related manuals for CP-C9SM

Brands by name

Popular brands

Hitachi CP-C9SM, Service Manual

Search results

Summary of Contents for CP-C9SM

Reviews:

Related manuals for CP-C9SM

Brands by name

Popular brands