43
DW
2
U
5.3 VIDEO COLOR TEMPERATURE ADJUSTMENT
(STD)
Preparation
(1) Same as “Video Color Temperature adjustment:
(HIGH)”. For 55” video level changes to 0.700Vp-p.
Adjustment
(1) Perform the following adjustment with the remote
control.
(2) Set the CRT color analyzer (CA-100) at the center of
the panel.
(3) Set color temperature to “STD”.
(4) Ensure that Adjustment R/G/B DRIVE (STD) are all
set as FF.
(5) After receiving White raster signal, step down the two
(or one) among Adjustment R/B/G DRIVE (STD) and
adjust the value shown below.
At least one of the data should be FF.
5.4 VIDEO COLOR TEMPERATURE ADJUSTMENT
(B/W)
(Only for HDX models)
Preparation
(1) Same as “Video Color Temperature adjustment:
(HIGH)”. For 55” video level changes to 0.700Vp-p.
Adjustment
(1) Perform the following adjustment with the remote
control.
(2) Set the CRT color analyzer (CA-100) at the center of
the panel.
(3) Ensure that Adjustment R/G/B DRIVE (B/W) are all
set as FF.
(4) After receiving White Raster signal, step down the
two (or one) among Adjustment R/B/G DRIVE (B/W)
and adjust the value shown below.
At least one of the data should be FF.
Remarks
(1) Same as “Video Color Temperature adjustment
(HIGH)”
Specification
Video Color temperature (STD)
x = 0.314
42"
±
0.005
y = 0.327
±
0.005
(
Color temp
:
6500K
)
x = 0.314
55"
±
0.005
y = 0.327
±
0.005
(
Color temp
:
6500K
)
Specification
Video Color temperature (B/W)
x = 0.335
42"
±
0.005
y = 0.343
±
0.005
(
Color temp
:
5400K
)
x = 0.335
55"
±
0.005
y = 0.343
±
0.005
(
Color temp
:
5400K
)
6
.
DIGITAL MAIN CHECK
6
.1
SYSTEM SOFTWARE VERSION CHECK
Please Insert MMC card
ove
Return
(5) The upgrading process begin by filling a
bar, when finish the message will say,
“Upgrade complete …” when this appear
unplug the TV from the AC line outlet to
complete the process.
(6) Now plug again the TV and verify the
new software version.
(7) The Main software version will display the
latest version issue by design.
NOTE:
(1) A Service Bulletin will be sent when a
new version is issued officially to the
Service Department every time the soft-
ware version needs to be modified.
(2) In case that the upgrade fails or when a
CARD is inserted with new version and
can’t upgrade ; please perform the
FACTORY RESET
process to the TV,
then try upgrading again.
(1) Press Menu button on the R/C or control
panel.
(2) Enter the SETUP options, and then look
f
or UPGRADES option.
(3) The Main software version will be display
V0100.0000
as
shown
o
n Fig. 1.
(4) If this version needs to be change for a
design improvement or failure, please
select the Upgrade Now button.
Fig. 1
Software version
Reset The Software
Setup
Move
SEL
Return
Software Version # : Main Vxxxx.xxxx
MMC Software Upgrade
Upgrade Now
Please Insert MMC card before upgrading.
Reset TV Settings
No Yes
OR
(Select "Yes" to return all settings to the factory
default after main power OFF/ON.)
Summary of Contents for 42HDS69 - 42" Plasma TV
