11
3 Message List
Messages
Data
Description
[ ]: Omissible
[ ]: Omissible, ( ): Response data
Standard Commands
*IDN?
(<Manufacturer name>,<Model name>,<Serial number>,<Software
version>)
Queries the Device ID (Identify code).
*RST
Initializes the device.
*TST?
(<PASS/FAIL>)
Initiates a self-test and queries the result.
*TRG
Requests the measurement start.
*OPC
Sets OPC of SESR after all operations that are being
executed are completed.
*OPC?
Responds with ASCII “1” after all operations that are
being executed are completed.
*WAI
Executes subsequent commands after command
processing is completed.
*CLS
Clears the Event Registers and the Status Byte
Register.
*ESR?
0 to 255
Reads and clears the Standard Event Status Register
(SESR).
Event Registers
:ESR0?
(0/2/4/6)
Queries Event Status Register 0 of the Standard
Operation Register Group.
Communications Settings
:SYSTem:COMMunicate:LAN:IPADdress
<IP address>
Sets the IP address.
:SYSTem:COMMunicate:LAN:IPADdress?
(<IP address>)
Queries the IP address.
:SYSTem:COMMunicate:LAN:CONTrol
<Port No.>
Sets the LAN port.
:SYSTem:COMMunicate:LAN:CONTrol?
(<Port No.>)
Queries the LAN port.
:SYSTem:COMMunicate:LAN:SMASk
<Subnet mask>
Sets the Subnet mask.
:SYSTem:COMMunicate:LAN:SMASk?
(<Subnet mask>)
Queries the Subnet mask.
:SYSTem:COMMunicate:LAN:GATeway
<Address>
Sets the default gateway.
:SYSTem:COMMunicate:LAN:GATeway?
(<Address>)
Queries the default gateway.
:SYSTem:COMMunicate:LAN:UPDate
Reflects the LAN settings.
:SYSTem:MAC?
(<MAC address>)
Queries the MAC address.
Trigger
:TRIGger:SOURce
< BUS/ EXTernal >
Sets the trigger source.
:TRIGger:SOURce?
(< BUS/ EXT >)
Queries the trigger source.
:TRIGger:DELay
<Delay time (sec)>
Sets the trigger delay.
:TRIGger:DELay?
(<Delay time (sec)>)
Queries the trigger delay.
:TRIGger:EDGE
<RISE/FALL >
Sets the trigger detection edge.
:TRIGger:EDGE?
(<RISE/FALL >)
Queries the trigger detection edge setting.
Measurement Mode
:MODE
<NORMal/DARK/PULSe>
Sets the measurement mode.
:MODE
(<NORM/DARK/PULS>)
Queries the measurement mode.
Modulation Frequency Measurement Settings
:PULSe:AVERaging
<Average times>
Sets the number of average times of the modulation
frequency measurement.
:PULSe:AVERaging?
(<Average times>)
Queries the number of average times of the
modulation frequency measurement.
:PULSe:EDGE
<RISE/FALL >
Sets the period detection edge of the SYNC signal.
:PULSe:EDGE?
(<RISE/FALL >)
Queries the period detection edge of the SYNC
signal.
Modulated Light Function
:PULSe
<1/0/ON/OFF>
Sets the modulated light function.
:PULSe?
(<1/0 >)
Queries the modulated light function.
:PULSe:FREQuency
<Modulation frequency [Hz]>
Sets the modulation frequency.
:PULSe:FREQuency?
(<Modulation frequency [Hz]>)
Queries the modulation frequency.