manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 89 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 89

81

 

7

External Control (EXT.I/O)

The EXT.I/O terminal on the rear panel of the instrument supports external control by 
providing output of the TEST and comparator judgment signals, and accepting input 
of the START and STOP signals.
All signals are isolated with photocouplers. (The input/output common terminals are 
shared.) The input circuit can be switched to accommodate either current sink output 
(NPN) or current source output (PNP) by the internal settings of the instrument.
Check the input/output ratings and internal circuit structure, understand the safety 
precautions for connecting a control system, and use accordingly.

Signal output or input

Check the controller input and output specifications.

Set the EXT.I/O mode switch (NPN/PNP) on the instrument.
(Operate the switch after the instrument power is turned off.)

Connect the EXT.I/O terminal to the signal output and input.

Set the instrument.

7  External Control (EXT.I/O)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments