manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 83 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 83

75

 

6

Saving and Loading Measurement 
Conditions (Memory function)

Panel save function

The current measurement conditions can be saved.
Up to 10 patterns of measurement conditions can be saved and retained even when 
the power is turned off.

Settings that can be saved with the panel save function

 

•

Test voltage

 

• Range (including auto range ON/OFF and resistance range for the fixed range)

 

•

Test speed

 

•

Test duration

 

•

Response time

 

• Comparator upper and lower limit values (including comparator ON/OFF)

 

•

Test mode

 

•

Judgment beep sound

Panel load function

The measurement conditions saved by the panel save function are loaded.
The measurement conditions can be loaded by the operation key, RS-232C 
command, or EXT.I/O.

6 

Saving and Loading Measurement Conditions (Memory function)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments