manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 46 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 46

38

Switching the Measurement Speed (FAST/SLOW)

3.3  Switching the Measurement Speed (FAST/

SLOW)

There are two measurement speeds, 

[FAST]

 and 

[SLOW]

. The resistance is 

measured and displayed in 30 ms when the measurement speed is set to 

[FAST]

 and 

in 500 ms when the speed is set to 

[SLOW]

.

Setting the measurement speed to 

[SLOW]

 is effective if a measured value fluctuates 

and it is difficult to read the value.

1

 

Open the Settings screen.

Select 

[SET]

.

2

 

Set the test speed.

Selection

[SLOW]

[FAST]

Return to the 
Measurement 
screen.

IMPORTANT

 

•

The sampling time is 100 ms even when the measurement speed is set to 

[FAST]

 

if the contact check function is ON.
(The sampling time is 500 ms if the measurement speed is set to 

[SLOW]

 

regardless of the function check setting.)

 

•

If the test duration is set to less than 500 ms when the measurement speed is set 
to 

[SLOW]

, the measured value is not displayed. Set a test duration that is longer 

than the sampling time.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments