manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 182 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 182

Appx.

2

Contact Check Function

Appx. 2  Contact Check Function

Route 3

Output terminal 
LOW side

Route 2

LOW side

Protective 
resistance

High voltage 
power supply
(Output voltage)

Contact check terminals

HIGH side

Output terminal 
HIGH side

Equipment to 
be measured

Protective resistance

Partial 
resistance

Partial 
resistance

Detection 

resistance

Detection 

resistance

Detection 

resistance

Internal power 
supply DCV

V1

V2

V3

A

(Figure: Contact check)

Route 1

A contact check is performed independently for the output terminal HIGH side and 
LOW side. The principle of a contact check is shown below.

Principle

HIGH side contact check:
Using output voltage monitor V1 and contact check voltage monitor V2, the voltage of the 
measurement terminal is measured and whether the output voltage is reliably applied to the 
terminal is checked. (Route 1)

LOW side contact check:
Internal power supply (DCV) for a contact check on the LOW side and current (voltage) detector 

V3 are provided. A contact check is performed by V3 that detects the current from DCV flowing 

the electrode of the equipment to be measured. (Route 2)
As  resistance is normally detected by Route 3, DCV for a contact check on the LOW side does 
not affect resistance measurements.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments