Hioki ST5520 Instruction Manual Download Page 153

Page: 153 / 201

145

Command Reference

:Panel:CLEar

Deletes the test conditions.

Syntax

:Panel:CLEar <data1>

<data1>

Test condition number 1 to 10 (NR1 numerical data)

Example

To delete Test condition 1

PC>

:Panel:CLEar 1

:AOUT:RANGe

Sets whether the analog output is to be output in all measurement resistance ranges or in each
range display area.

Syntax

:AOUT:RANGe <data>

<data>

FULL/EACH (text data)

FULL: Output in all measurement resistance ranges

EACH: Output in each range display area

Example

To set to output in all measurement resistance ranges
PC>

AOUT:RANGe FULL

:AOUT:RANGe?

Queries the analog output setting.

The FULL or EACH setting is returned in text data (<data>).

Syntax

:AOUT:RANGe?

Response

:AOUT:RANGE <data>

or simply

<data>

<data>

FULL/EACH (text data)

FULL: Output in all measurement resistance ranges

EACH: Output in each range display area

Example

To query the output method (when the setting is FULL)

PC>

:AOUT:RANGe?

ST5520>

:AOUT:RANGE FULL

(when

the

:HEADer

command is ON)

ST5520>

FULL

(when the

:HEADer

command is OFF)

:PROBe

Sets the 9299 Switched Probe operation mode.

During a test, the test is stopped and the operation mode is set.

Syntax

:PROBe <data>

<data>

CONTinue/TRIGger (text data)

CONTinue: Continuous mode

TRIGger: Trigger mode

Example

To set continuous mode
PC>

: PROBe CONTinue

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 153 / 201

Search results

Summary of Contents for ST5520

Reviews: