manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 147 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 147

139

Command Reference

:SHORtcheck

Sets the short circuit check function ON/OFF.

Syntax

:SHORtcheck <data>

<data>

ON/OFF (text data)

ON: The short circuit check function is enabled.

OFF: The short circuit check function is disabled.

Example

To set the short circuit check function to ON

PC> 

:SHORtcheck ON

:SHORtcheck?

Queries the short circuit check function ON/OFF setting. The setting is returned in text data (<data>).

Syntax

:SHORtcheck?

Response

:SHORTCHECK <data>

 or simply 

<data>

<data>

ON/OFF (text data)

ON: The short circuit check function is enabled.

OFF: The short circuit check function is disabled.

Example

To query the short circuit check function (when the short circuit check 

function is enabled)

PC>

:SHORtcheck?

ST5520>

:SHORTCHECK ON

  (when the 

:HEADer

 command is ON)

ST5520>

ON

 

 

(when the 

:HEADer

 command is OFF)

:SHORtcheck:TIME

Sets the short circuit check time.

Set 0.0 when the short circuit check time is set to auto (AUTO).

Syntax

:SHORtcheck:TIME <data>

<data>

Short circuit check time (unit: second) 0.0 and 0.010 to 1.000 (resolution 

0.001) (NR2 numerical data)

Example

To set the short circuit check time to 0.5 seconds

PC>

:SHORtcheck:TIME 0.5

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments