Hioki ST5520 Instruction Manual Download Page 125

Page: 125 / 201

117

Automatically Exporting Measured Values at the Ends of Tests (Data output function)

8.3 Automatically Exporting Measured Values at

the Ends of Tests (Data output function)

When a test is completed, the instrument can send measured values automatically as
data to a computer via the RS-232C interface.

If the START key is pressed with TYPE 1 or TYPE 2 selected, do not send any

commands to the instrument until the computer receives the measured values.
Doing so may cause measured values to be sent twice.

Open the Settings screen.

Select

[SET]

Set

[DATA OUT]

[ON]

Selection

OFF (Automatic

exporting is

disabled.)
TYPE1

(Automatic

exporting in TYPE 1

format is enabled.)

TYPE2
(Automatic
exporting in TYPE 2

format is enabled.)

Return to the
Measurement
screen.

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 125 / 201

Search results

Summary of Contents for ST5520

Reviews: