manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 114 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 114

106

Interlock Function

7.7  Interlock Function

The interlock function is used to cut off any output from the instrument by linking with 
an external device.
Once the interlock function is activated, all key operations are disabled.
When the interlock function is enabled in the I/O screen of the EXT.I/O Settings 
screen, the interlock function runs when Pin 3 of EXT.I/O (INTERLOCK) is ON.

1

 

Connect pin 3 of EXT.I/O (INTERLOCK) to ISO_COM (pin 9, pin 27).

(p. 83)

2

 

Check that 

[LOCK]

 at the upper right corner is not lit on the 

Measurement screen.

If 

[LOCK]

 is lit, there is a possibility of a connection failure. Check the connection 

performed in step 

1

.

3

 

Open the Settings screen.

Select 

[SET]

.

4

 

Make the settings for 

INTERLOCK

.

Selection

[ON]

[OFF]

Return to the 
Measurement 
screen.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments