Hioki SM7860 Series Instruction Manual Download

Page: 43 / 64

EXT I/O Connector and Signals

Signal Functions

Input Signals

EXT_DCV2 (+24V)

External power source input

OUTPUT

Output on/off setting

OUT1 (1)_ON to OUT1 (8)_ON

Specific-channel on/off setting

OUT2 (1)_ON to OUT2 (8)_ON

Specific-channel on/off setting

OUT3 (1)_ON to OUT3 (8)_ON

Specific-channel on/off setting

OUT4 (1)_ON to OUT4 (8)_ON

Specific-channel on/off setting

INTERLOCK

When on, no voltage can be generated.

•

The INTERLOCK signal cannot be used unless it has been enabled with the operating environment

setting (CNF=0).

•

The device ships with this setting disabled (CNF=1).

Refer to “CNF” (p. 36)

•

The output voltage cannot be changed while the OUTPUT signal is enabled.

Output Signals

ALARM

Generated voltage alarm

BUSY

Voltage being output

TEMP

Temperature alarm

Summary of Contents for SM7860 Series

































































Search results

Summary of Contents for SM7860 Series

Reviews:

Related manuals for SM7860 Series

Brands by name

Popular brands

Hioki SM7860 Series, Instruction Manual

Search results

Summary of Contents for SM7860 Series

Reviews:

Related manuals for SM7860 Series

Brands by name

Popular brands