Hioki MR8827 Instruction Manual Download Page 234

Page: 234 / 436

229

Waveform Calculation Settings

(If necessary)
Set auto-saving (p. 82) and auto-printing (p. 109).

Execute the calculation.

Apply Calculations to Existing Data

At the

[Wave Calc]

sheet, select

[Exec].

To calculate while measuring

Press the

START

key to start measurement.

Calculation waveforms are displayed after loading waveforms.

11.2.1 Display the Trigger Settings to Search Measurement Data

The results of waveform calculation are displayed on the Waveform screen.

CH1 Waveform

Example: Calculate the absolute value of the waveform of CH1.

Calculation equation = ABS(CH1)

Absolute Value Waveform

To copy settings from one calculation to another

Settings can be copied at the

[Wave Calc]

sheet.

Refer to “8.9 Copy Settings to Other Channels (Copy Function)” (p. 163)

aveform Calculation Functions

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 234 / 436

Search results

Summary of Contents for MR8827

Reviews: