manualshive.com logo in svg

Hioki MR8827, Instruction Manual

Share
Download
Hioki MR8827 Instruction Manual Download Page 223

218

Calculation Result Judgment

10.3.1  Display Judgment Results and Signal Output

Numerical calculation judgment results are displayed on the Waveform screen.

Within the judgment threshold range:   GO judgment

Out of the judgment threshold range:   NG judgment (displayed in red)

When printing, judgment results for each parameter will also be printed.

When the judgment result is GO

 • The GO signal is output at the GO

――

/EXT.OUT.1

―

―

―――

――

 external I/O terminal.

When the judgment result is NG

 • The NG signal is output at the NG

――

/EXT.OUT.2

―

―

―――

――

 external I/O terminal. The NG judgment is asserted when 

any channel is judged as NG.

 • When the beeper is enabled, a beep sounds when a result is out of the threshold range.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands