Hioki MR8827 Instruction Manual Download Page 214

Page: 214 / 436

209

10 Numerical Calculation Functions

Numerical Calculation

Functions

Numerical calculations can only be used with the Memory function.

Results calculated from the acquired waveform are displayed as numerical values on the Waveform

screen. These calculation results can be judged for evaluation. Numerical calculation settings are made

on the Status screen -

[Num Calc]

sheet.

To Open the

[Num Calc]

Sheet

Press this key repeatedly to

display the various sheets.

[Status]

[Num Calc]

Operations Available From the [Num Calc] Sheet

Numerical Calculations

•Average

•RMS (Root-Mean-Square) value

•Peak-to-Peak Value (P-P Value)

•Maximum Value

•Time to Maximum Value

•Minimum Value

•Time to Minimum Value

•Period

•Frequency

•Rise Time

•Fall Time

•Standard Deviation

•Area

•X-Y Area

•Time to Level

•Level at Time

•Pulse Width

•Duty Ratio (%)

•Pulse Count

•Four Arithmetic Operations

•Time difference calculation

•Phase differnce calculation

•High level calculation

•Low level calculation

(24 types in total)

•

Specified calculation between AB

cursors

Waveform calculations can be

limited to data within the range

specified by the AB cursors.

Calculation operator details: “10.6

Numerical Calculation Type and

Description” (p. 222)

Numerical Calculation Judgment (p. 216)

The result of a numerical calculation can be

compared to a preset reference range, for GO/NG

(Pass/Fail) evaluation.

There are 24 types of numerical calculations in total,

16 of which can be performed simultaneously.

When the Scaling function is used, numerical

calculation is performed on scaled values.

Save/Print Numerical Calculation Results

•Auto-save numerical calculation results

•

Save specified existing numerical calculation result

Refer to “10.4 Save Numerical Calculation Results” (p. 219).

•Auto-print

•Arbitrary printing

Refer to “10.5 Print Numerical Calculation Results” (p. 221).

Numerical Calculation Functions

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands