Hioki MR8827 Instruction Manual Download Page 202

Page: 202 / 436

197

Trigger by Timer or Time Interval (Timer Trigger)

9.5 Trigger by Timer or Time Interval (Timer Trigger)

This trigger allows you to record at fixed times.

•

Triggering occurs at the specified interval from the specified Start time until the Stop time.

•

Before setting up a Timer Trigger, verify that the clock is set to the correct time. If not, set the clock on

the System screen -

[Init]

sheet. (p. 46)

Procedure

Press the

DISP

key to open the Waveform screen, and then press the

TRIG.SET

key to open the trigger settings

window.

Enable or disable the timer trigger.
Move the cursor to the

[Timer Trig]

item.

Off

Timer triggering disabled.

Timer triggering enabled.

Start Time

Stop Time

Interval

Records for the specified recording length

START

key

(When

[On]

is selected)

Set Start and Stop times.

Move the cursor to

[M]

[D]

[h]

and

[m]

to set recording

Start and Stop times.

Set the date and time.

To set to the current date and time, select

[Present Time]

(To apply a trigger through the specified interval, from

Start to Stop)
Set the Interval.

Move to cursor to

[D]

[h]

[m]

and

[s]

[Interval]

Set the recording interval.

Press the

START

key.

Measurement starts and recording will start at the specified

Start time.

To stop recording early, press the

STOP

key.

When the specified interval

is shorter than the specified

recording length:

Start Time

Stop Time

Interval

Records for the specified recording

length

START

key

When the recording length exceeds

the specified interval

The next trigger is not applied until

the data for the specified recording

length has been acquired.

When the recording length exceeds

the stop time

Recording time depends on the operating

function.

(p. 198)

When the interval is set to zero

If the

[Repeat]

trigger mode is

selected, or the REC or MEM functions

are used, recording is repeated from

Start to Stop times.

The timer trigger time and the time at which the trigger is actually fired may differ by up to 3 sample

times.

Trigger Settings

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands