Hioki MR8827 Instruction Manual Download Page 177

Page: 177 / 436

172

Detailed Settings for Modules

8.10.6 Setting Model 8971 Current Unit

There is no need to change the setting since it is set when the clamp sensor is automatically

recognized.

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Mode

20A/2V

Sets this option when Model 9272-10 (20 A range), 9277, or CT6841

Clamp Sensor is connected. (Default setting)

200A/2V

Sets this option when Model 9272-10 (200 A range), 9278, CT6863, or

CT6843 Clamp Sensor is connected.

50A/2V

Sets this option when Model CT6862 Clamp Sensor is connected.

500A/2V

Sets this option when Model 9279, 9709, CT6844, CT6845, CT6846*, or

CT6865* Clamp Sensor is connected.

* When Model CT6846 or CT6865 is connected to Model 8971 Current Unit through

Model 9318 Conversion Cable, the instrument recognizes that as an 500 A AC/DC

sensor is connected; set the scaling ratio to 2.00.

Range

Current measurement (

Default setting)

RMS

RMS current measurement

8.10.7 Setting Model 8972 DC/RMS Unit

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Mode

Switches between voltage measurement and RMS measurement.

Voltage measurement

(Default setting)

RMS

RMS measurement

Response

The response time for RMS measurement can be set to three speeds: Fast, Normal

and Slow.

While it is normally set to

[Fast]

, this can be changed to

[Normal]

[Slow]

stabilize the measured value when the frequency is low or when severe fluctuations

are present.

Fast

Response time about 100 ms.

(Default setting)

Normal

Response time about 800 ms.

Slow

Response time about 5 s.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands