manualshive.com logo in svg

Hioki MR8827, Instruction Manual

Share
Download
Hioki MR8827 Instruction Manual Download Page 171

166

Detailed Settings for Modules

8.10.1  Settings for the Anti-Aliasing Filter (A.A.F.)  

(Model 8968 High Resolution Unit)

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

A.A.F

Enable the anti-aliasing filter to remove aliasing distortion. The cutoff frequency 

automatically changes according to the timebase or, when the FFT function is used, 

the frequency range setting.

Off

The anti-aliasing filter is disabled.  (

Default setting)

On

The anti-aliasing filter is enabled.

(When external sampling is used, the antialiasing filter (AAF) is not 

available.)

8.10.2  Probe Attenuation Selection

Refer to “To Open [Each Ch] and Make a Channel Selection” (p. 164).

Probe

Set this when performing measurement with a connection cable or probe.

1:1

Model L9197, L9198 or L9217 Connection Cord connected to the input 

module.  (

Default setting)

10:1

Model 9665 10:1 Probe connected to the input module.

100:1

Model 9666 100:1 Probe, P9000-01/-02 Differential Probe connected to the 

input module.

1000:1

Model 9322 Differential Probe, P9000-01/-02 Differential Probe connected 

to the input module.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands