manualshive.com logo in svg

Hioki MR8827, Instruction Manual

Share
Download
Hioki MR8827 Instruction Manual Download Page 151

146

Add Comments

Entering Numerals By Incrementing/Decrementing

1 

Move the cursor to the numeric input field and select 

[Up-Down]

.

A virtual keyboard for digit input will be displayed.

2 

Enter numerals at the virtual keyboard.  

(Use 

F1

 and 

F2

 to move digit position, and use 

F3

 and 

F4

 to increase or decrease the value.)

3 

Select 

[Confirm] 

to accept the entry.

Press the 

ESC

 key to cancel the input.

Enter Numerals With a Numeric Keypad

1 

Move the cursor to the numeric input field and select 

[Tenkey Entry]

.

A virtual keyboard for numeric keypad input will be displayed.

2 

Enter numeral at the virtual numeric keypad.

ESC

:  Cancel input

BS

: 

Delete 1 character

C

: 

Delete all characters

Enter

:  Accept the entry

3 

Select 

[Confirm] 

to accept the entry.

Press the 

ESC 

key to cancel the input.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands