Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 90

Page: 90 / 137

10.1.9.6

LOAD SENSOR

The ECM3 load cell sensor calibration is possible only after

having inserted the relevant password.
Load cell sensor calibration procedure and password are

detailed in the APPENDIX 2.

10.1.9.7

INCLINATION SENSOR

The tilt sensor calibration is possible only after having

inserted the relevant password.
Tilt sensor calibration procedure and password are detailed

in the in the APPENDIX 1.

10.1.9.8

EXTRA

EXTRA menu gives the access to other settings and under

menus.
The here aside picture shows the EXTRA menu display, from

EXTRA menu pressing button from n.1 to n.6 it’s possible to

enter into further pages. Pressing button n.9 (ESC) brings

back to the SETUP menu.

10.1.9.8.1

FIRMWARE

Check the dedicated procedure

10.1.9.8.2

CARDS

Check the dedicated procedure.

INCLINATION

SENS

CALIBRATION

MACCHINA:
NOT READY

3 CALIBR.

9 ESC

LOAD SENS

CALIBRATION

MACCHINA:
NOT READY

3 CALIBR.

9 ESC

EXTRA

1 OPTIONAL

2 FIRMWARE

3 CARDS

4 MODEM

5 GPS

9 ESC

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands