Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 117

Page: 117 / 137

117

APPENDIX 7

–

ACOUSTIC RECALL DEVICES

Machine is equipped with remote control beeper and the horn, horn is installed

on the base, closed to the engine, it is activated by remote control buttons 5
and 6 press together.

As opinions is available the warning buzzer. when installed warning buzzer is

installed within the electric components compartment, looking from the back
side it is on the left of the electric motor.

The table here below details the functioning of remote control beeper and
warning buzzer.

REMOTE

CONTROL

BEEPER

WARNING

BUZZER

(optional)

CONDITION

EVENTUAL FURTHER

CONDITION

OFF

Emergency stop pressed

OFF

Alarm LOAD MAX

OFF

Alarm LOAD MIN

OFF

No outrigger at the ground

Photocell signal OFF

Aerial part inclination limit

OFF

No outrigger at the ground

OFF

Tracks speed control activated

OFF

Aerial part movement in progress (*)

OFF

Lithium pack remainig capacity <20%

WARNING

BUZZER

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands