Hinowa LightLift 15.70 3S Technical Course Booklet Download Page 111

Page: 111 / 137

111

APPENDIX 3 - REMOTE CONTROL JOYSTICK CALIBRATION

Using the joysticks the operator selects the movement to be carry out, the

direction and the speed. The direction of the joystick determines the movement
direction, the more the joystick is moved the faster will be the movement.
The following table details the movement controlled and its direction depending

on the joystick shifting direction.

JOYSTICK DIRECTION

AERIAL MOVEMENT

FORWARD

LEFT TRACK FORWARD

BACKWARD

LEFT TRACK BACKWARD

FORWARD

1ST AND 2ND BOOMS UP

BACKWARD

1ST AND 2ND BOOMS DOWN

FORWARD

3RD BOOM UP

BACKWARD

3RD BOOM DOWN

FORWARD

TELESCOPE IN

BACKWARD

TELESCOPE OUT

FORWARD

BASKET ANTICLOCKWISE ROTATION

BACKWARD

BASKET CLOCKWISE ROTATION

FORWARD

JIB UP

BACKWARD

JIB DOWN

FORWARD

TURRET ANTICLOCKWISE ROTATION

BACKWARD

TURRET CLOCKWISE ROTATION

FORWARD

RIGHT TRACK FORWARD

BACKWARD

RIGHT TRACK BACKWARD

RIGHTWARD

BASKET LEVELLING FORWARD

LEFTWARD

BASKET LEVELLING BACKWARD

1 2 3 4 5 6 7 8

Summary of Contents for LightLift 15.70 3S










































































































































Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands

Hinowa LightLift 15.70 3S, Technical Course Booklet

Search results

Summary of Contents for LightLift 15.70 3S

Reviews:

Related manuals for LightLift 15.70 3S

Brands by name

Popular brands