Hino 238 Workshop Manual Download Page 490 | Manualshive

Page: 490 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1267

DTC: P259F

EN01H16F01030F03001155

P259F: Nozzle operating range failure -WIDE (VNT actuator wiping error (too wide range))

INFORMATION

1. Technical description

•

The VNT actuator steplessly operates the nozzle via the REA (Rotary Electric Actuator) and controls turbine speed
and boost pressure.

•

The VNT actuator (REA) has a position sensor and constantly monitors the target opening and the actual opening.

•

Wiping operation is carried out when the engine is stopped and the soot, oil, and other impurities accumulated in the
vane working range are removed. Also, the turbocharger mechanical working range is checked for trouble.

<Description of malfunction>

•

–

2. DTC set condition

(1) DTC detection condition

•

While the engine is in operation: Always

•

While the engine is stopped: During wiping operation.

(2) Judgement criteria

3. Reset condition

•

After normal operation is restored and the starter switch is on the "LOCK" position.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

•

Cruise control function is not available.

•

Auxiliary brake function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

•

Cruise control does not work.

•

Auxiliary brake does not work.

Item

Details (Reference)

1. Wiping failure

When a wiping operating range wider than HI range is detected 2 times.

VNT controller

10

8

1

5

6

7

4

2

3

3

2

4

5

8

1

14

12

6

11

7

VNT actuator
(REA)

Engine

ECU

Power

(VNTV)

(VNTG)

CAN H

CAN L

Relay

Fuse

Battery

SAPH16F010300991

«
...
488
489
490
491
492
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Vauxhall Pages: 177

Brand: Toyota Pages: 371

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

Autostacker PL-6SR

Brand: BendPak Pages: 104

Brand: Nav TV Pages: 3

Brand: Condor Pages: 2

Brand: walser Pages: 24

Brand: CALIMA Pages: 9

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Cadillac Pages: 20

Brand: Saab Pages: 15

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Lantronix Pages: 51

Brand: Ratio Pages: 12

Brand: Horn Tools Pages: 8

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Brand: ADS Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands