manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1

ENGINE CONTROL SYSTEM (J08E)

4-001

4

ENGINE CONTROL SYSTEM......................................4-3

PRECAUTIONS FOR DIAGNOSIS.........................4-3
SYSTEM BLOCK DIAGRAM...................................4-5
SYSTEM DIAGRAM................................................4-6
PRECAUTIONS ......................................................4-8
SENSOR LOCATION ............................................4-11
COMPUTER (ECU) PIN ASSIGNMENT...............4-20
ENGINE ECU CONNECTOR................................4-24
INSPECTION ........................................................4-28
DIAGNOSIS USING THE PC DIAGNOSIS
TOOL.....................................................................4-29
DIAGNOSTIC TROUBLE CODE (DTC)
TABLE ...................................................................4-30
GROUP SHARING THE SENSOR POWER SUPPLY 
TERMINAL ............................................................4-45
GROUP SHARING THE SENSOR GND
TERMINAL ............................................................4-46
ENGINE BASIC INSPECTION SHEET
(ENGINE INSPECTION CHECK SHEET) ............4-47
NO DTC ................................................................4-50
DTC: P0016 ..........................................................4-53
DTC: P003A ..........................................................4-57
DTC: P0045 ..........................................................4-64
DTC: P0047 ..........................................................4-71
DTC: P0048 ..........................................................4-78
DTC: P006E ..........................................................4-85
DTC: P006F ..........................................................4-90
DTC: P007B ..........................................................4-95
DTC: P007C and P007D.....................................4-113
DTC: P0088 ........................................................4-122
DTC: P0096 ........................................................4-146
DTC: P0097 and P0098 ......................................4-161
DTC: P00AF........................................................4-170
DTC: P0101 ........................................................4-175
DTC: P0104 ........................................................4-187
DTC: P0106 ........................................................4-195
DTC: P0108 ........................................................4-202
DTC: P0112 and P0113 ......................................4-210
DTC: P0115 ........................................................4-219
DTC: P0117 and P0118 ......................................4-231
DTC: P011A ........................................................4-241
DTC: P011C........................................................4-252
DTC: P0122 and P0123 ......................................4-260
DTC: P0128 ........................................................4-273
DTC: P016E and P016F .....................................4-280
DTC: P0182 and P0183 ......................................4-304

DTC: P0191 ........................................................4-313
DTC: P0192 and P0193 ......................................4-335
DTC: P01A5 ........................................................4-346
DTC: P01A6 ........................................................4-355
DTC: P0200 ........................................................4-364
DTC: P0201, P0202, P0203, P0204, P0205 and
P0206..................................................................4-367
DTC: P0217 ........................................................4-376
DTC: P0219 ........................................................4-383
DTC: P0222 and P0223 ......................................4-390
DTC: P0234 ........................................................4-402
DTC: P0237 ........................................................4-409
DTC: P0263, P0266, P0269, P0272, P0275 and
P0278..................................................................4-418
DTC: P026C and P026D.....................................4-434
DTC: P0299 ........................................................4-452
DTC: P0300 ........................................................4-459
DTC: P0301, P0302, P0303, P0304, P0305 and
P0306..................................................................4-469
DTC: P0335 ........................................................4-481
DTC: P0336 ........................................................4-489
DTC: P0340 ........................................................4-497
DTC: P0341 ........................................................4-504
DTC: P0381 ........................................................4-512
DTC: P0401 ........................................................4-519
DTC: P0402 ........................................................4-537
DTC: P0404 ........................................................4-550
DTC: P0405 and P0406 ......................................4-557
DTC: P041B ........................................................4-564
DTC: P041C and P041D.....................................4-579
DTC: P0420 ........................................................4-589
DTC: P0489 and P0490 ......................................4-596
DTC: P049D........................................................4-603
DTC: P04D5 and P04D6.....................................4-610
DTC: P0500 and P0501 ......................................4-619
DTC: P0504 ........................................................4-627
DTC: P0519 ........................................................4-635
DTC: P0524 ........................................................4-639
DTC: P0562 and P0563 ......................................4-646
DTC: P05F1 ........................................................4-654
DTC: P0605 ........................................................4-664
DTC: P0606 ........................................................4-667
DTC: P0607 ........................................................4-670
DTC: P0610 ........................................................4-673
DTC: P0611 ........................................................4-677
DTC: P0617 ........................................................4-680

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Brand: Taffio Pages: 8
FVC Sprinter Bed System Adventure Wagon Kit Installation Manual preview
Sprinter Bed System Adventure Wagon Kit
Brand: FVC Pages: 8
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Brand: Mercedes-Benz Pages: 30
DEFA 412737 Fitting Instructions Manual preview
412737
Brand: DEFA Pages: 7
Prorack K869 Fitting Instructions Manual preview
K869
Brand: Prorack Pages: 15
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Brand: Edelbrock Pages: 4
RAM 2012 Truck Chassis cab Owner'S Manual preview
2012 Truck Chassis cab
Brand: RAM Pages: 506
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Brand: Pet Gear Pages: 4
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Brand: v.LOGiC Pages: 22
Subaru 2003 Baja Owner'S Manual preview
2003 Baja
Brand: Subaru Pages: 32
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Brand: Cadillac Pages: 482
curt CM-58967 Installation Manual preview
CM-58967
Brand: curt Pages: 4
Ford 2000 F 350 Owner'S Manual preview
2000 F 350
Brand: Ford Pages: 256
Westin 28-21030 Instructions preview
28-21030
Brand: Westin Pages: 3
Pyle PLPSC8 User Manual preview
PLPSC8
Brand: Pyle Pages: 14
FAAFTECH FT-RC-RN Installation Manual preview
FT-RC-RN
Brand: FAAFTECH Pages: 2

Brands by name

Popular brands

Load more brands