Hino 238 Workshop Manual Download Page 31

Page: 31 / 919

ENGINE CONTROL SYSTEM (J08E)

4–808

DTC: P119F

EN01H16F01030F03001102

P119F: Fuel rail pressure sensor - rationality

INFORMATION

1. Technical description

•

The common rail pressure sensor consistently measures common rail pressure.

<Description of malfunction>

•

Common rail pressure cannot be correctly sensed.

•

Malfunction is likely to have occurred in the common rail pressure sensor.

2. DTC set condition

(1) Check conditions

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V.

•

The conditions described above remain for 5 seconds or longer.

•

Common rail pressure is 220 MPa or less.

•

No other diagnosis codes are present (the monitor disable DTC table can be referred to)

(2) Judgement criteria

P119F is detected under the conditions described below. 1 and 2 represent the order of priority.

1. A difference in voltage remains higher than 1.06 V for 3 seconds or longer.

2. A difference in voltage remains less than 0.04 V for 3 seconds or longer.

3. Reset condition

•

After normal operation is restored and starter switch LOCK.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

Common rail
pressure sensor

Engine

ECU

LLJ (PCR+)

VCC2

LCE (PCR3)

K8N (PCR-)

GND1

K8P (PCR)

KRP

K6E

KRX

K6D

SIG1

(AVC1)

(PCR2)

(AGD1)

(PCR1)

(AGD2)

K8M (PCR+)

KRY

VCC1

(PCR4)

LLK (PCR-)

LL3

GND2

(AVC2)

LLH (PCR)

KRQ

SIG2

PCR-

K8N

PCR-

K8N

PCR-

K8N

PCR-

K8N

PCR-

K8N

PCR-

K8N

Pressure limiter

Flow damper

Pressure sensor

Common rail

SAPH16F010300648

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands