Hino 238 Workshop Manual Download Page 205

Page: 205 / 919

ENGINE CONTROL SYSTEM (J08E)

4–982

DTC: P2122 and P2123

EN01H16F01030F03001127

P2122: Accelerator pedal position sensor 1 - out of range (Out of range low)

INFORMATION

1. Technical description

•

–

<Description of malfunction>

•

The accelerator sensor 1 cannot correctly sense.

2. DTC set condition

(1) Check conditions

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V.

•

The engine has stopped (stalled) or runs at 500 r/min or higher for continuous 5 seconds or longer.

(2) Judgement criteria

•

Accelerator sensor 1 (accelerator pedal position sensor) voltage

≤

0.6 V (-15.4 %)

•

Failure timer

≥

1 second

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Cruise control function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Cruise control does not work.

<Symptoms on the vehicle due to malfunction>

•

Cruise control does not work.

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Harness disconnection or short-circuit

•

Malfunction of sensor 1

•

Malfunction of engine ECU

Accelerator
sensor 1
(accelerator pedal
position sensor)

K5Z

(ACS1)

K8Z

(GND1)

(SIG1)

KRS

(AVC4)

LCS

K91

(ADG8)

(VCC2)

(GND2)

K62

K92

(ACS2)

(SIG2)

KRR

K8Y

(AVC3)

(VCC1)

LCR

K5Z

KRS

LCS

K62

KRR

LCR

K90

(ADG7)

K93

K8Z

K91

K92

K8Y

K90

K93

Engine

ECU

SAPH16F010300759

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands