Hino 238 Workshop Manual Download Page 200

Page: 200 / 919

ENGINE CONTROL SYSTEM (J08E)

4–977

DTC: P2120

EN01H16F01030F03001126

P2120: Throttle/Pedal Position Sensor/Switch "D" Circuit

INFORMATION

1. Technical description

•

–

<Description of malfunction>

•

Neither of accelerator sensors are properly functioning.

2. DTC set condition

(1) DTC detection condition

•

Engine ECU power supply voltage is in the range of 10 V to 16 V.

•

Starter switch ON.

•

Engine running or starter LOCK

(2) Judgement criteria

•

Both sensors are out of order at the same time.

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Cruise control function is not available.

•

Idling stop system is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Cruise control does not work.

•

Idling stop system does not work.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Malfunction of both sensors

•

Malfunction of engine ECU

Accelerator
sensor

Engine

ECU

K5Z

(ACS1)

K8Z

(GND1)

(SIG1)

KRS

(AVC4)

LCS

K91

(ADG8)

(VCC2)

(GND2)

K62

K92

(ACS2)

(SIG2)

KRR

K8Y

(AVC3)

(VCC1)

LCR

K5Z

KRS

LCS

K62

KRR

LCR

K90

(ADG7)

K93

K8Z

K91

K92

K8Y

K90

K93

SAPH16F010300755

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands