Hino 238 Workshop Manual Download Page 185

Page: 185 / 919

ENGINE CONTROL SYSTEM (J08E)

4–962

DTC: P2101

EN01H16F01030F03001124

P2101: Intake throttle valve - functional

INFORMATION

1. Technical description

•

Increase temperature during DPR automatic regeneration by throttling intake air utilizing Intake throttle.

•

Assist engine stop by closing when starter switch is off.

<Description of malfunction>

•

Stuck diesel throttle is detected.

2. DTC set condition

(1) DTC detection condition

•

Stable operational condition

- Engine revolution fluctuation range less than 20 r/min

- Engine injection quantity fluctuation range less than 2 mm

/st. cyl

•

Normal intake throttle circuit

•

Continuation of the above condition for 10 seconds

(2) Judgement criteria

•

Difference between Actual and Target is more than



10 % for 80 seconds

3. Reset condition

•

After normal operation is restored and engine is restarted after engine stall.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

•

Idling stop system is not available.

•

Cruise control function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

•

Idling stop system does not work.

•

Cruise control does not work.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Air cleaner: Restricted

•

Air hose:

- Collapsed

- Loose or leaking

•

Body of throttle:

- Excessive dirt inside body of diesel throttle

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Hino 238, Workshop Manual, Page: 185 / 919

Search results

Summary of Contents for 238

Reviews: