Hino 238 Workshop Manual Download Page 118 | Manualshive

Page: 118 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–895

DTC: P1515

EN01H16F01030F03001115

P1515: Charge air undercooling

INFORMATION

1. Technical description

•

The intercooler cooling efficiency is monitored by comparing the intake temperature and intercooler outlet tempera-
ture measured by the air flow sensor.

<Description of malfunction>

•

Intercooler cooling efficiency drop is detected.

2. DTC set condition

(1) DTC detection condition

•

Engine is running (not stopped).

(2) Judgement criteria

•

The intake temperature is -15



C {5



F} and the intercooler outlet temperature is

≥

74



C {165



F}.

•

The intake temperature is 65



C {149



F} and the intercooler outlet temperature is

≥

146



C {295



F}.

3. Reset condition

•

Just after restoration to normal condition.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is detected after test drive.

8. Estimated failure factors

1. Insufficient cooling air

•

Foreign substance clogging intercooler outer fins

•

Foreign substance clogging radiator outer fins

•

Deformed or clogged intercooler outer fin

•

Deformed or clogged radiator outer fin

•

Foreign substance clogging air inlet at front of vehicle

2. Faulty intercooler

•

Tube abnormal swelling or cracking

3. Faulty part other than intercooler

•

Engine cooling fan failure

•

Fan clutch failure

•

Clogged air cleaner

«
...
116
117
118
119
120
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

RadioPRO 5 RP5-GM41

Brand: PAC Pages: 3

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: EEZ RV Pages: 31

Brand: Subaru Pages: 16

Brand: Hank Pages: 2

Brand: RAM Pages: 13

Brand: Linear Logic Pages: 8

Brand: Yakima Pages: 12

Brand: Subaru Pages: 44

Brand: Prorack Pages: 14

Brand: Magneti Marelli Pages: 2

Brand: Buick Pages: 112

Brand: Nav TV Pages: 8

Brand: Haltech Pages: 13

Brand: Whispbar Pages: 18

Brand: Volvo Pages: 304

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands