Hino Motors J08E-VC Page 207 Workshop Manual Download | Manualshive

Page: 207 / 339

background image

FUEL SYSTEM (J08E)

EN07–6

OVERHAUL

EN0110607H200001

IMPORTANT POINTS - DISMOUNTING

! CAUTION

While working, be careful not to make dirt and water enter parts.

1.

TURN THE STARTER SWITCH TO THE LOCK POSITION.

! WARNING

Perform the following work after the engine cools off to avoid fire or
burning. The fuel in the common rail could have a high temperature
(approx. 100



C {212



F}) immediately after driving.

2.

FUEL DISCHARGE

(1)

Prepare reservoir under the drain pipe to receive the drained fuel.

(2)

Remove the drain plug of the bubble separator.

(3)

Loosen the bleeder plug of the bubble separator.

(4)

Drain until no more fuel comes out.

(5)

Tighten the drain plug and the bleeder plug of the bubble separator.

Tightening Torque:
Drain plug: 5.9-7.9 N



m {60.2-80.5 kgf



cm, 4.4-5.8 lbf



ft}

Bleeder plug: 5-8.8 N



m {51-89.7 kgf



cm, 3.7-6.5 lbf



ft}

! CAUTION

Drain the fuel in accordance with the regulation of disposal specified
in each region.

3.

REMOVING THE FUEL FILTER

(1)

Remove the fuel filter and the fuel pipe.
Refer to the chapter

"AIR INTAKE SYSTEM"

4.

REMOVING THE INTAKE PIPE

(1)

Remove the intake pipe.
Refer to the chapter

"AIR INTAKE SYSTEM"

5.

DISCONNECTING THE HARNESS

(1)

Disconnect the connector connected to each of the suction control
valve of the supply pump and the fuel temperature sensor.

SAPH011060700006

Bleeder plug

Drain plug

SAPH01Z080700001

Fuel temperature
sensor

Suction control
valve

SAPH011060700008

«
...
205
206
207
208
209
...
»

Summary of Contents for J08E-VC




















































































































































































































































































































































Reviews:

No comments

Related manuals for J08E-VC

Brand: phytron Pages: 29

Brand: W&H Pages: 42

Char-Lynn H Series

Brand: Eaton Pages: 13

Brand: Man Pages: 90

Brand: Jula Pages: 17

Brand: Suzuki Pages: 91

Smart Motor SM23166MT

Brand: MOOG ANIMATICS Pages: 32

Brand: Lenze Pages: 76

ERS VAR10 SZ 2500

Brand: Warner Pages: 16

Brand: Motorola Pages: 82

Brand: A'OK Pages: 7

Brand: JetCat Pages: 54

Brand: Viessmann Pages: 14

Brand: dunkermotoren Pages: 30

MotorLift RA20F

Brand: Chamberlain Pages: 24

Brand: Chamberlain Pages: 40

Brand: LOBSTER SPORTS Pages: 5

Brand: Fagor Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands