background image

6 SPEED FAN & LIGHT

REMOTE CONTROL

INSTALLATION INSTRUCTIONS

Model: 980014-R

READ AND SAVE THESE INSTRUCTIONS

INSTALLING THE WALL CONTROL

REMEMBER

  to turn off the power before you begin.

NOTE -

 Secures to any surface or application: flat wall, single gang 

box, multi gang box. 

Option 1. Flat Surface Installation

1.   Select a desired location. Use the wall plate to mark the location of 

the mounting holes. Plastic wall anchors or mounting screws are 

needed for this application. (Fig. 1) 

2.   Seat the cradle B into the wall plate. Secure the wall plate to the 

wall using the provided hardware.

3.   Snap the face plate cover onto the wall bracket.

4.   Remote transmitter will be held in place with built in magnets. 

Option 2. For single gang box

1.   Remove the existing wall plate and the old switch from the wall 

outlet box.

2.   Seat the cradle A into the wall plate. (Fig. 2) 

3.   Connect the black lead wires from the switch in the cradle A to the 

black wires in the switch box. Hot input wire to one of the cradle A 

switch leads. Power lead to the fan is connected to the remaining  

switch lead.

4.   Connect the wall plate / cradle A assembly to the wall outlet box  

using the supplied hardware.

5.   Snap the face plate cover onto the wall bracket.

6.   Remote transmitter will be held in place with built in magnets. 

Option 3. Multi Gang Wall Switch Box Installation

1.   Remove the existing wall plate and old switch from the wall outlet 

box. (Fig. 3) 

2.   Connect the black lead wires from the switch in the cradle A to the 

black wires in the switch box. Hot input wire to one of the cradle 

switch leads. Power lead to the fan is connected to the remaining 

switch lead. (Fig. 4)

3.   Attach the cradle A to the wall switch box using the supplied 

hardware.

4.   Attach the multi-gang faceplate to the switch set in the wall outlet 

box. Cradle A of Hinkley switch will fit in any standard decora face 

plate.

5.   Remote transmitter will be held in place with built in magnets.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Outlet box

Transmitter

Face plate

Wall plate

Cradle A

Outlet box

Face plate

Switch

Outlet box

Transmitter

Face plate

Cradle A

Transmitter

Face plate

Wall plate Cradle B

Wall

Plastic 

anchor

Summary of Contents for 980014-R







Reviews: