background image

 

200/250 DOUBLE SLAT/RUSH ROCKER

  

ASSEMBLY INSTRUCTIONS 

 

 

                         Thank you for purchasing a quality select hardwood double rocker.  These rockers are made exclusively by 
                         the Hinkle Chair Company, a family-owned business that has made hardwood furniture in the same location in  
                         Springfield Tennessee since 1834.  Your chair comes with a rich heritage and will become a treasured family 
                         heirloom.  If you should have any comments or questions or need these instructions in Spanish, please call the 
                         toll-free number below between 8:00 AM and 4:30 PM CST Monday through Friday.  Again, we appreciate  
                         your business and hope you get many years of enjoyment from this chair. 
 
                        Espa

ň

ol: Si usted tiene cualquier comentario o preguntas o necesita estas instrucciones en espa

ň

ol por favor 

                        yame al numero de llamada gratuita 1-800-251-3025 entre las horas de 8:00 AM y 4:30 PM hora central de 
                        Lunes a Viernes. 
 

       NOTICE:  The Rocker that you have purchased requires some assembly.  As with all furniture,  proper  
        assembly is necessary for the safe and comfortable use of your bench.  Hinkle Chair cannot be responsible for  
        any damage or injury that results from improper assembly of the bench.  Please read and follow these instructions  
        carefully and in sequence.  If you have any questions please call The Hinkle Chair Company helpline (800) 251-3025 
        

 

4669 Mt. Sharon Rd.     P.O. Box 410     Springfield, TN. 37172 

   

 

 

 

       800-251-3025                615-384-8477    Fax 615-384-0055 

www.hinklechaircompany.com

 

 
 
 
 

 

Summary of Contents for 200










Reviews: