hilscher NANL-B500G-RE User Manual Download

Page: 64 / 90

Commissioning

64/90

Step 1: Identify IP address of the device.

Open the

Ethernet Device Configuration

program.

Scan for devices.

Your analyzer device NANL-B500G-RE is displayed.

Figure 19: Ethernet Device Configuration - NANL-B500G-RE found (Example)

Read the IP address of the NANL-B500G-RE device whose firmware
you want to update. For the example shown in the figure above, the IP
address is

192.168.1.1

For details to the

Ethernet Device Configuration

program refer to

the

operating instruction manual

Ethernet Device Configuration,

Address setting for Ethernet capable Hilscher devices

Step 2: Upload current firmware image

Open a web browser.

Enter the IP address in the web browser's address bar and press the
Enter key.

The netANALYZER configuration page is displayed.

Below

Firmware image update

: Click

Browse

A dialog for file selection is displayed.

Select the firmware update file

nanl-b500g-re.update

. The

firmware update file is located on the product DVD in the folder

NANL-

B500G-RE firmware update

Click

Open

Click

Upload to device

During the upload process,

uploading

is displayed in front of the

Upload to device

. This process takes a few seconds.

Summary of Contents for NANL-B500G-RE



























































































Search results

Summary of Contents for NANL-B500G-RE

Reviews:

Related manuals for NANL-B500G-RE

Brands by name

Popular brands

hilscher NANL-B500G-RE, User Manual

Search results

Summary of Contents for NANL-B500G-RE

Reviews:

Related manuals for NANL-B500G-RE

Brands by name

Popular brands