background image

 

 

27 

 

Avis d'Industrie Canada 

Cet appareil est conforme à la norme CNR-210 des règlements d’Industrie Canada. Son fonctionnement est sujet aux deux 
conditions  suivantes:  1)  Cet  appareil  ne  doit  pas  provoquer  d’interférences  et  2)  Cet  appareil  doit  accepter  toutes  les 
interférences, y compris celles pouvant entraîner son dysfonctionnement. Cet appareil numérique de la classe B est conforme 
à la norme NMB-003 du Canada Avis d’Industrie Canada sur l’exposition aux Rayonnements: Cet appareil est conforme 
aux limites d’exposition aux rayonnements d’Industrie Canada pour un environnement non contrôlé. 
 

EU Conformity Statement 

This product is marked with "CE" and comply therefore with the applicable harmonized European standards listed under the 
Radio Equipment Directive 2014/53/EU. 
This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. 
The  equipment  named  above  is  confirmed  to  comply  with  the  requirements  set  out  in  the  Council  Directive  on  the 
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2004/108/EC) and Low-voltage 
Directive (2014/35/EU). 
The equipment passed the test which was performed according to the following European standards: 
• EN55032:2015 
• EN55035:2017 
• EN 61000-3-2:2014 
• EN 61000-3-3:2013+A1:2019 
•EN 62368-1:2014 

 

Summary of Contents for A200 Series




























Reviews: