Hillrom Welch Allyn Connex ProBP 3400 Service Manual Download Page 51

Upgrades and licenses

Welch Allyn supports software and license upgrades for this device.

Software upgrades, when available, may be purchased or provided at no charge to customers
covered by a Welch Allyn Service Agreement. The upgrades can be installed by either a Welch Allyn
service center or by the customer using the service tool, Silver or Gold edition. Customers choosing
to install software upgrades on their own will receive the software via the internet. When ordering
software, provide the serial number of the device you wish to install the software on.

Licenses are available for purchase to enable additional software features. Customers who want to
install licenses themselves must have the service tool, Silver or Gold edition, installed on a PC with
internet access. Customers who have purchased a license receive an authorization code to enter in
the service tool. The code authorizes the service tool to download the license file from the Welch
Allyn server. The service tool then installs the license on the connected device, enabling the new
feature. A more detailed description of the license process can be found in the service tool help
files.

NOTE 

When a license authorization code is used to activate the license, the

authorization code is married to the device serial number. Save the license
authorization code with the serial number for future use. If the main board is
replaced, you will need the authorization code to reactivate the license.

Available upgrades and licenses

The following upgrades and licenses can be added to each model’s base configuration.

Supported software upgrades

Software updates and upgrades are supported for the Host Controller and ModF (Blood Pressure)
module. New software upgrades are announced on the product page of the Welch Allyn website
as they become available.

Licensed features

Model

Bluetooth

SureBP

34XX

34BX

47

Summary of Contents for Welch Allyn Connex ProBP 3400

































































Reviews: