manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 90

Accessories

76

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Line Managers (P7512) 

WARNING:

To help prevent personal injury and/or equipment 
damage, follow these warnings and cautions:

•

Warning

—Do 

not

 use the line managers 

to secure ventilator tubing; use only 
approved ventilator tubing devices. 

•

Warning

—Do 

not

 wrap power cords 

around the line managers.

The line managers help keep lines such as IVs, 
suction tubing, and monitor cables together and away from the articulation of the frame. 

A

CCESSORIES

 

FOR

 I

NTERNATIONAL

Oxygen Tank Holders (AC959, AD101, and AD102)

WARNING:

Warning

—Do not exceed the load capacity of the oxygen tank holders; refer to the value shown on the 

holder. To do so could cause personal injury and/or equipment damage.

The oxygen tank holders are designed to hold an oxygen tank. Each holder is designed to hold a 
specific-sized oxygen tank and must never be used with a different size oxygen tank.

When you use one of the oxygen tank holders, follow these recommendations:

•

Make sure that the oxygen tank holder is correctly inserted into one of the equipment sockets 
at any of the four corners of the bed.

•

Make sure that the oxygen tank is correctly inserted in the holder.

•

Do not use a different oxygen tank model from the model specified. The tank could fall or 
interfere with other operations.

•

Make sure that the holder is in a safe position before you adjust the tilt of the bed or lower the 
bed.

•

If the holder does not permit the bed to pass through a doorway, adjust the holder so that it is 
at the front of the bed or put the holder and cylinder on the bed (remember to return the 
holder to its normal location after the transport).

Pivoting 3-Liter Cylinder holder (AC962)

We recommend that you install the cylinder holder at the foot end of the bed. 

WARNING:

Warning

—Do not exceed the load capacity of the cylinder holder; refer to the value shown on the 

holder. To do so could cause personal injury and/or equipment damage.

When you use the cylinder holder, follow these recommendations:

•

Make sure that the holder is correctly inserted in either equipment socket at the foot end of the 
bed.

•

Make sure that the 3-liter cylinder is correctly inserted in the holder.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands