manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 87

Accessories

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 73 

To Install

1.

Remove the cover from the Patient Helper mount on the bed. Keep the cover.

2.

Turn the arm assembly so that it is towards the left or right side of the bed, and 
install the arm assembly into the Patient Helper mount.

3.

Pull the T-handle that is on the Patient Helper mount until the arm assembly 
lowers into position.

4.

Install the horizontal arm into the arm assembly, and insert the pull pin to hold 
the horizontal arm in position. 

5.

Install the clamp of the trapeze handle assembly on to the horizontal arm, and 
tighten the clamp to attach the trapeze handle assembly to the horizontal arm.

6.

Turn the arm weldment so the trapeze handle is centered over the bed and the 
T-handle locks into position.

To Remove

1.

Pull the T-handle that is on the Patient Helper mount, and turn the arm assembly 
so that the trapeze handle is over the side of the bed.

2.

Loosen the clamp that attaches the trapeze handle assembly to the horizontal 
arm, and remove the trapeze handle assembly from the horizontal arm.

3.

Remove the pull pin and horizontal arm from the arm assembly.

4.

Remove the arm assembly from the Patient Helper mount.

5.

Install the cover on to the Patient Helper mount.

Patient Pendant (P7803A01/02)

To Install

1.

Put the pendant into position in the opening from the 
patient side of a head-end siderail.

2.

Set the top edge of the pendant into the siderail so it 
engages the upper section of the siderail.

3.

Rotate the lower edge of the pendant inward until it 
clicks into position inside the siderail.

When the pendant is not in use, we recommend that you 
keep it stored in its slot in the siderail.

To Remove

Gently pull the pendant out from the siderail.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands