manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 47

Standard Features

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 33 

30° Head Angle Alert

Bed Width Adjustment

When plugged into AC power, the sleep deck width can be adjusted to either 40"or 50" (102 cm or 127 
cm). This automated adjustment control adjusts both the bed frame and the surface. The 
communication cable that connects the air supply unit to the bed frame must be fully connected and 
the four thumbscrews tightened for the powered width controls to operate. See “Install the Surface and 
Air Supply Unit” on page 57.

WARNING:

To help prevent personal injury and/or equipment damage, obey these warnings:

•

Warning

—Make sure there are no objects or devices near or under the bed, especially when 

the bed width is extended, that may interfere with or contact the bed when lowering.

•

Warning

—Keep the patient within the surface perimeter during width adjustments. 

The Head Angle Alert control is on the caregiver control pod next to the display. When 
set, if the head section goes below 30°, these will occur:

•

The display will flash five times.

•

An audible alert will come on.

•

The alert indicator will flash. 

Set the Alert

1.

Raise the head section to the applicable position 

above

 30°.

2.

Press the 

Enable

 key.

3.

Press the 

Alert

 control. The alert indicator will come on and you will hear a single 

beep.

NOTE:

When the bed operates on battery power the display will be off and the alert disabled. 

Respond to the Alert

Raise the head section above 30° or deactivate the alert through the caregiver 
control pod.

Deactivate the Alert

1.

Press the 

Enable

 key.

2.

Press the 

Al

ert control. The alert indicator will go off and you will hear a single 

beep.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands